Carving Set

How to Prepare Your Hand Carved Stone for Hanging

I have seen many different methods used for hanging hand carved stone on your wall or garden fence.  These range from a piece of wire or metal adhered to the back of the stone to a hole in the stone itself and everything in between.  Where as all these things have been effective lets look at the pros and cons of each and see what works best for your application.  We will also cover some steps that should be taken to prepare your stone carving for hanging.

The initial thing that must be done to hang your hand carved stone is to make sure you place the hanging implement you choose in the correct place on the stone so that your carved design will hang correctly.  I call this step balancing the stone.   To do this you must find the place on the carved piece so that when you lift the stone off your surface the bottom of your stone stays parallel with the surface you have lifted it from.   I use an old set of tongs to pick the stone up, adjusting the tongs positions up or down and side to side until I get the perfect parallel lift.  Before removing the tongs mark the spot on the back side of your stone carving where the tongs are touching the stone.  This gives you your balancing point.

You can then use this spot to attach the hanging device of your choice.  If you choose to hang your carved stone with a single hook, that hook should be attached to this spot with a strong adhesive, I prefer a two part adhesive.  The single hook will leave a bit of space between the wall and your stone carving but it is fairly easy to attach.  If you choose to hang your piece with a wire you should attach the wire so that the middle of the wire is over your balancing spot.  The wire should then be attached at either end with a strong adhesive, again I prefer a two part epoxy.   This method leaves a less space between the wall and your stone carving than the hook all though it is a little more complicated.  The method I prefer for my hand carved stone designs is to actually drill a hole into the back of the stone carving.

If you choose to drill a hole on the back of your carved stone for hanging you might want to do this prior to actually hand carving the stone because there is always a chance of breaking your carved piece.  I choose to drill a hole on the back of my stone carvings for hanging because this allows the piece to hang flat against whatever surface you are displaying your stone carving on and you can also use the same hole to stand the piece if you choose to do so.  I prefer to use a diamond covered drill to make the hole.  Please refer to my article Helpful Tools and Tips for Hand Carved Stone for the use and care of these bits.  You can also use a hammer drill with a regular bit.

I have covered some of the methods for hanging your carved stone as well as what I feel is the most important step in the process which is balancing your stone carving.   As I find with each of the processes in stone carving I am always learning better and easier way to accomplish every step.  Check back often as I will continue to share my knowledge and hopefully make this gratifying art form accessible to all.

About the Author

Ron White, stone carver and entrepreneur, has been carving stone since 1993 and is shown in more than 40 galleries across the US. Prior to beginning his work with hand carved stone Ron has worked extensively with leather, wood cabinetry and even jewelry. Learn more about Ron White, his work, or purchase your own selection at http://www.derivedfromnature.com.

How to Carve a Halloween Pumpkin : Halloween Pumpkin Carving Set Up

Totally Bamboo 20-7930 3-Piece Cutting Board Set $11.95 This 3-piece bamboo cutting board set includes three cutting boards. Boards measure 6 by 8 by 3/8-inch, 8-1/2 by 11 by 3/8-inch and 9-1/2 by 13 by 3/8-inch. Don’t be caught again without an extra cutting board. 3/8 of an inch thick means that these boards are maneuverable and easy to store. Made up of strong, bamboo. They’re also durable; they have a tri-ply, cross laminate construction with a sp…

Victorinox 47547 10-1/4-Inch Wavy Bread Knife, Black Fibrox Handle $23.50 Nothing is worse than going to cut with your bread, and having the handle slip around in your hand. To combat this potential for injury, Victorinox has created this Fibrox bread knife. The Fibrox® handle is textured and provides a firm grip, even when wet, and does not slip or slide around. It is comfortable and fits naturally to the shape of your hand, and provides an attractive and modern styli…

OXO Good Grips 10-1/2-by-15-Inch Utility Cutting Board, Black Edge $14.99 Quality kitchen tools can easily turn tedious meal preparation into a fun culinary experience. OXO’s Good Grips utility cutting board has all the makings of a top-notch cook’s aid. Crafted from thick polypropylene, the surface is durable, nonporous, and odor resistant; it is also impervious to deep scratches and maintains the sharp edges on kitchen knives. A juice groove around the perimeter of on…

Pro-Quality 20-Piece Diamond-Point Bit Set for Rotary Tool – Glass, Stone, Ceramic $1.10 Professional Quality, 1/8 in. Shank, 180 Grit. Includes 20 assorted shapes covered with diamond particles. All bits have 1/8 in. shanks and come in convienient plastic holder. Excellent for fine detail work, cutting, engraving, carving, touch-up and finishing. Use on wood, jade, ceramic, glass, hardened steel, semi-precious stones and other hard materials….

SE Pick Set, 12Pc Stainless Steel Wax Carvers $9.77 Some uses for these instruments are: amateur and professional taxidermy; cleaning archaeological artifacts; uncovering and cleaning fossils and shells; woodworking and furniture refinishing; ceramics, mosaics and pottery work; wood and clay carving; soap and candle carving; computer and mechanical work; doll-making and repair; and much more!…

Dremel 710-05 160 Piece Accessory Kit $29.74 This is a handy accessory kit for organized storage of the popular Dremel accessories. The kits consists of regular and heavy duty cut off wheels, drum sander, sanding bands, sandpaper discs, polishing compounds, felt polishing wheels, paste brush, carbon steel brush, aluminum oxide grinding stones, silicon carbide grinding stones, dressing stone, 1 8-inch bit, mandrels, wrench, lawn mower and gar…

Secrets of the Parthenon $0.99 …

The Holy Grail $1.99 …

Frank Russell’s Power Carving Fur, Feathers, & Fins: How to Carve with Foredom Power Tools and Accessories $25.34 With more than three hours of instructional material, this DVD details the steps involved in transforming blocks of tupelo wood into carvings of the cottontail rabbit, mallard drake duck, and smallmouth bass. Viewers will learn everything needed for these projects, from power carving basics, such as roughing out a blank, to making finishing touches, including detailed segments on expertl…

SE 5 Pc Probe Set, Size 5 1/2-6 $1.74 Made in China, Size Range from Approx. 5 1/2 in. to 6 in….